Guide

How to Disassemble a Computer Chair

Updated on · By the I Love Homey team

Here's how to disassemble a computer chair: flip it upside down, pull the wheels, then separate the cylinder from the base and the seat. Work on a padded floor, keep the screws in a bag, and use a rubber mallet instead of force.

On this page (10 sections)
  1. Why would you take a computer chair apart?
  2. What tools and space do you need before you start?
  3. How do you remove the wheels from a computer chair?
  4. How do you separate the base from the cylinder?
  5. How do you free a stuck cylinder?
  6. How do you take the seat and back off the mechanism?
  7. How do you pack the parts for a move?
  8. How do you put the computer chair back together?
  9. Which parts are worth replacing while the chair is apart?
  10. What mistakes should you avoid when you take a chair apart?

Here's how to disassemble a computer chair: flip it onto a padded floor, pull the wheels, then separate the cylinder from the base and the seat. Keep the screws together, use a rubber mallet instead of brute force, and the whole job takes about 20 minutes on most chairs.

You don't need a workshop to take a computer chair apart. A mallet, a screwdriver and a towel under the frame cover almost every step, and most of the parts are designed to pull straight out.

Why would you take a computer chair apart?

You split a chair for three main reasons: moving, repair, or deep cleaning. Each one needs a slightly different amount of disassembly, so decide your goal before you start pulling.

For a move, the base and the wheels are usually enough. The chair then fits in a car trunk or a box far more easily, and the weight drops.

For repair, you'll likely go further. A sinking seat points to the cylinder, a wobbly frame points to bolts or the base, and a jammed wheel points to the casters.

Our guide on how to fix a wobbly office chair covers the tightening steps if you'd rather try that first.

For cleaning, the seat and back detach from the mechanism and clean up quickly. Our walkthrough on how to clean an office chair explains the fabric and mesh methods.

What tools and space do you need before you start?

A rubber mallet, a Phillips screwdriver, a towel and a few zip bags cover most computer chairs. Add a flathead screwdriver for prying stubborn clips and work gloves if the cylinder is greasy.

Clear a flat area about 4 by 4 ft. A rug or a folded towel protects both the chair's finish and the floor, and it stops plastic parts from skidding when you tap them.

Have a tray or a bowl for small parts. Label a bag for the seat bolts so they don't get mixed with the armrest screws.

Check the chair's weight before you flip it. Most task chairs are heavy at the base, so lift from the seat and lower it gently rather than dropping it.

How do you remove the wheels from a computer chair?

Grip each caster and pull straight down out of its socket. Most casters are friction-fit stems, so they slide out by hand, and a firm twist helps if one is tight.

Flip the chair so the base faces up. Work around the star base one wheel at a time, pulling evenly so the base doesn't tip.

Stuck caster? Tap the stem socket lightly with a mallet, then try again.

Don't pry with a metal bar, because the plastic socket can crack.

Set the wheels aside in a bag. If one is worn, flat-spotted or noisy, this is the moment to fit new ones, and our guide on how to replace office chair wheels has the size check you need.

If your stems measure 11 mm, the BF BRIGHTFIELD set is the other option. Both sets skip the floor mat, since the soft wheels glide on wood and tile without scratching.

How do you separate the base from the cylinder?

Hold the base and pull the cylinder straight up, or tap the base loose with a mallet. The cylinder sits in a tapered socket, so it releases along its axis, not at an angle.

Lay the chair on its side with the base toward you. Grip the star base with one hand and the cylinder column with the other, then pull them apart.

If it won't budge, stand the base on the floor and tap around the socket with a rubber mallet. Keep the blows light and even, and avoid hitting the gas cylinder's shiny shaft.

Don't use a hammer or a pipe wrench. A metal tool can score the shaft or crack the base, and a damaged cylinder won't hold height safely.

Some chairs have a retaining clip or a bolt under the seat plate. Check for one before you pull, and remove it with the screwdriver if you find it.

How do you free a stuck cylinder?

Use a cylinder removal tool or a mallet, never heat or a lever against the gas shaft. The tool grips the cylinder below the seat and lets you pull it free without damaging the mechanism.

Slide the tool over the column, tighten it as the instructions show, then tap or twist until the cylinder releases. This is the step most people struggle with, and the right tool saves a lot of time.

That kit also suits a chair whose seat sinks on its own mid-workday. Swap the cylinder while the chair is already apart, then rebuild it in reverse.

If you don't have a removal tool, try a few sharp mallet taps on the base socket. Stop if the plastic starts to crack, and let a bike shop or repair bench pull it instead.

How do you take the seat and back off the mechanism?

Turn the chair upright and unscrew the bolts that hold the seat plate to the mechanism. Most chairs use 4 bolts under the seat, and the back panel often has 2 to 4 more.

Tip the chair onto its side and photograph the bolt layout first. Then loosen each bolt a half turn before removing them all, which keeps the plate from twisting.

Keep the bolts in their labeled bag. Armrests usually bolt through the seat pan, so remove them first if they block access.

On many chairs the back is separate, held by a bracket or a pair of bolts at the hinge. Support the back with one hand as the last bolt comes out so it doesn't drop.

Some mesh backs use push clips instead of bolts. Squeeze the clip tabs with a flathead screwdriver and lift the back free.

How do you pack the parts for a move?

Keep small parts with their own section and wrap the base and cylinder separately. That way nothing scratches and reassembly stays quick at the other end.

Wrap the base in a towel or bubble wrap and tape the wheel bag to it. Put the seat bolts in a zip bag taped to the seat plate, so they travel with the part they fit.

Lay the cylinder flat, not standing, and keep the gas shaft from pressing against anything heavy. The mechanism goes in its own bag with the armrest screws.

Label each bag by part, not by number. "Seat bolts" tells you more at the new place than "bag 3."

How do you put the computer chair back together?

Reverse the order: seat plate, mechanism, cylinder, base, wheels. Clean each socket first, then seat every part fully before tightening bolts.

Slide the cylinder into the base socket and press until it seats. Fit the wheels by pushing each stem in until it clicks or stops.

Bolt the mechanism to the seat, then the back and arms. Tighten the bolts in a cross pattern, a little at a time, so the plate sits flat.

Test the height lever and the tilt before you sit down. If the chair still feels loose, check the bolts again, and if the wobble is in the base, revisit the fixes in our wobbly chair guide.

Which parts are worth replacing while the chair is apart?

Once the chair is split, the wheels and the cylinder are the two parts worth upgrading, because both wear fastest. New casters protect your floors, and a fresh cylinder restores height.

Measure your caster stems before ordering, since IKEA chairs and some off-brand models use a different size. Both wheel sets here use a 7/16 inch by 7/8 inch stem.

Check the cylinder size too. The Office Oasis kit uses a 1-1/8 inch piston shaft and a 2 inch column, which fits most US office chairs.

A comfortable chair is also a rebuilt one. If yours still feels hard after the fix, see how to make an office chair more comfortable.

What mistakes should you avoid when you take a chair apart?

The big ones are forcing a stuck part, losing the bolts, and skipping the photo step. Each one turns a 20-minute job into a hunt for replacements.

Never hammer the gas cylinder shaft or heat it. Never lever a screwdriver under the seat plate until the plastic cracks.

And never mix seat bolts with armrest bolts, because the lengths differ.

If a part fights back, stop and look for a hidden clip or bolt first. That one habit is the difference between a clean teardown and a broken base.

Once you know how to disassemble a computer chair, the reverse is just as easy, and a chair that comes apart cleanly is a chair you can keep for years.

Frequently asked questions

Can I take a computer chair apart without any tools?

Often yes for the wheels and sometimes the base, since most casters pull straight out of their sockets by hand. The cylinder and the seat screws usually need a mallet or a screwdriver, so have both nearby before you start.

Do I have to remove the cylinder to disassemble a chair?

No. If you only need to move the chair or clean it, leave the cylinder in the seat and split the base and wheels only.

Pull the cylinder when it's worn, sinking or squeaking, since that's the part you'd replace.

How do I stop the screws and parts from getting lost?

Keep every screw in a labeled zip bag taped to the part it came from, and set small pieces in a tray as you go. Photos of each stage before you remove anything also make reassembly much faster.

Will the chair go back together as firmly as before?

Yes, if you clean the sockets, push each caster in until it seats, and tighten the seat screws evenly rather than one at a time. A chair that still wobbles after reassembly usually has a loose bolt or a worn cylinder rather than a broken frame.

Is it worth taking the chair apart to fix a squeak?

Only if the noise comes from the cylinder or a loose bolt. Clean and lube the moving joints first, and if the squeak stays, splitting the chair makes the source easy to find.

Most squeaks are solved without full disassembly.